May 1958 Radio-Electronics
Wax nostalgic about and learn from the history of early electronics. See articles
published 1929 - 1948. All copyrights hereby acknowledged.
Breaking news from May 1958: "Hardly a month passes nowadays without the announcement of some 'sensational' new amplifying device. The great
majority of these startling inventions, after their brief flurry in the popular and technical press, disappear into
oblivion. But we believe that the Tecnetron, just announced in France, has a brilliant and enduring future." Have
you ever heard of a Tecnetron? I didn't think so; neither had I before reading this article in Radio-Electronics.
I guess that pretty much negates the preceding prediction. The holy grail of the Tecnetron, whose etymology
in and of itself is worth reading about (it's not what you would guess), is that its
transconductance increases with frequency. Construction is such that although it is fabricated from a shaped rod
of germanium, it has a current controlling component that acts like a cross between a triode vacuum tube and a
depletion mode field effect transistor. My guess is that the rapid improvement of standard semiconductor junction
field effect transistors rendered the Tecnetron not just obsolete, but way too expensive to manufacture
The Tecnetron: Competitor to the Transistor?
Neither spacistor nor transistor, this new semiconductor triode shows great promise for the ultra-high frequencies
By E. Aisberg*
Close-up of a Tecnetron.
Hardly a month passes nowadays without the announcement of some "sensational" new amplifying device. The great
majority of these startling inventions, after their brief flurry in the popular and technical press, disappear into
oblivion. But we believe that the Tecnetron, just announced in France, has a brilliant and enduring future.
The most remarkable feature of this device i that it transconductance increases with frequency, unlike more common
semiconductor amplifiers whose performance falls off as frequency increases and becomes very low as the cutoff frequency
is approached. Up to the present, frequencies in the order of 500 mc have been attained with the Tecnetron. And, as
further work and research make it possible to reduce the capacitances of the contacts and other parts of the montage,
there seems to be nothing to prevent it from functioning at 1,000 mc or even higher.
It has been possible - with a Tecnetron working in class A at 500 mc - to obtain a power output of 30 mw, with
a dissipation of 125 mw. Since the characteristics of individual Tecnetrons are very consistent, one can envision
the paralleling of several identical units to obtain watts - or even kilowatts - of power. This may make it possible
to use Technetrons in applications requiring heavy currents.
In addition, the Tecnetron - though using germanium - is less sensitive to high temperatures than the transistor.
It will operate at temperatures 20°C higher than will transistors. This should extend its field of applications considerably.
A Tecnetron unit in its case.
Neither is it a fragile experimental device that works only under laboratory conditions. Pilot production by regular
industrial methods had begun on a small scale at the time of its announcement. About 700 units per month are being
produced, and indications are that production could quickly be increased to the thousands.
What is the Tecnetron?
First, why is it the Tecnetron? The first syllable of the name begins as does that of its inventor, S. Teszner.
The initials CNET follow. These stand for the Centre National d'Etude des Telecommunications (National Center for
the Study of Telecommunications), that great ensemble of research laboratories sponsored by France's Ministry of Posts,
Telegraphs and Telephones. And of course the final syllable is the conventional one for such electronic devices.
Now, how is the Tecnetron constructed? It is a small rod of n-type germanium, 2 mm in length and 0.5 mm in diameter,
provided with two contact electrodes at the ends. These must be of such material that they act solely like electrical
conductors and not like transistor junctions.
The germanium rod is reduced in diameter at its center (Fig. 1) to form a "bottleneck" of very small diameter (about
30 microns). Around this neck is placed a cylinder of indium. This makes a metal-to-semiconductor barrier-layer contact
of excellent characteristics. The ratio of forward-to-back resistance is greater than a million to one.
A relatively high potential (50 volts or more) is applied to the electrodes at the end of the rod. These may be called
the cathode and anode. The cylinder of indium might be called a grid, for it plays exactly that role. The inventor
prefers to call it the "bottleneck" or simply the "neck" to indicate its method of action better. The neck is polarized
negatively with respect to the cathode, and the circuit of a stage of amplification (Fig. 2) is like that of a tube
triode, with the load resistance placed in the anode circuit in series with the supply voltage.
Fig. 1 - Tecnetron cut to show cross-section of neck. The space charge E tends to drive the conducting area
toward the center of the rod.
Fig. 2 - Schematic of Tecnetron hookup.
Fig. 3-a - Distribution of charge carriers (electrons) with neck unbiased; 3-b reduction of current path
caused by negative bias on neck.
Fig. 4 - The Tecnetron can be considered as a variable resistance and a distributed variable capacitance.
Fig. 5 - Variation of the Tecnetron transconductance as a function of the signal frequency.
Fig. 6 - These Tecnetron static characteristic curves show the variation of anode current as a function of
anode voltage, for several neck voltages.
A field-effect transistor?
Is this device not essentially that which Shockley called a "field-effect transistor" which he described in the
Proceedings of the IRE (November, 1952; Vol. 40, pp 1365-76) and with which he was not able to obtain appreciable
gains above 2 mc? Like Shockley, Teszner has turned to the field effect, discovered by Lilienfeld in 1928. Here the
resemblance ends. Whereas Shockley worked with plane surfaces (or a parallelepiped), Teszner has utilized the cylindrical
configuration, transforming a linear effect to a quadratic one by applying a radial electric field.
What is the field effect? Our readers know of the Hall effect, due to which charge carriers in semiconductors can
be deflected from their paths under the action of a magnetic field. The Lilienfeld effect is analogous to the Hall
effect, but is based on the action of the electric instead of the magnetic field. In semiconductors such as germanium,
charge carriers (electrons or "holes") can be deflected from their paths by the action of such an electric field.
The Tecnetron action
The neck of the indium cylinder creates a concentrated electric field in the interior of the rod, depending on
the charge on the cylinder. With no charge whatever, the current is propagated evenly through the whole area of the
neck. As one applies a negative voltage to the cylinder, the electrons are deflected toward the center, occupying
only a reduced section of the rod (Fig. 3). Thus the apparent resistance of the rod increases as the active section
- through which electrons pass - decreases. This action is proportional to the square of the radius.
Note well that this is a variation in the total resistance, not in the specific resistivity which remains constant.
The voltage applied to the indium cylinder causes the neck to act as if its diameter were decreased. Thus the cathode-anode
current is varied, causing the voltage across the load resistor to reproduce faithfully the changes in the voltage
applied to the neck, but at a greater amplitude.
The best analogy of the Tecnetron is without doubt a flexible rubber hose through which flows a current of water.
If the hose is compressed more or less by the hand, the flow decreases in the same ratio. If the hose is compressed
circularly - from all sides toward the center, as by an encircling thumb and forefinger - the diminution of current
will follow the square law. This centripetal constriction is an essential characteristic of the Tecnetron.
Effects of capacitance
If we analyze these actions carefully, we note that the variation in resistance is accompanied by a variation in
capacitance between the part of the germanium occupied by the electrons and the indium cylinder. As the cylinder becomes
more negative, it drives the electrons further from it and toward the center of the rod, thus reducing the capacitance
between the current-carrying portion of the rod and the cylinder. As the voltage becomes less negative, the electrons
flow through a larger section of the germanium and the capacitance increases. The Tecnetron acts like the equivalent
circuit of Fig. 4.
These variations of capacitance, which are increased by the cylindrical configuration of the device, have an effect
on the current through the external circuitry similar to that which the variations of resistance have on the flow
of electrons through the germanium. These two actions are synchronous and reinforce each other, thus increasing the
gain. There is of course a very slight detuning effect in resonant circuits due to the instantaneous variations in
capacitance produced by the signal. These are very small, since the total input capacitance is a fraction of a micromicrofarad
and the detuning is proportional to the square root of the capacitance change. Practically, according to the inventor,
it manifests itself as a slight enlargement of the passband.
The capacitance effect, with its reduction of impedance as frequency increases, is one of the reasons for the high
transconductance at high frequencies (Fig. 5) and the fact that the Tecnetron's figure of merit continues to increase
with frequency. The figure of merit is the product of the gain by the width of the passband over which the gain is
maintained at ±3 db.
Tecnetron as amplifier
We have seen that the neck which acts as a control electrode is polarized negatively with respect to the cathode.
Thus no appreciable direct current can flow in the cathode-neck circuit, because of the extension of the barrier layer
into the n-type germanium.1
Under these conditions, the input resistance is several megohms. The input capacitance is in the order of 2 μμf.
The output impedance is generally higher than 1 megohm, and the load resistance thus may be chosen as high as it
is practically permissible to set it; usually between 2,500 and 250,000 ohms.
If we plot the characteristics of the Tecnetron by measuring the anode current as a function of the anode-cathode
voltage at various values of neck voltage, we obtain a family of curves which resemble strikingly those of a pentode
tube (Fig. 6). Which is to say, that we have here an excellent voltage amplifier. The chart shows experimental results
obtained at various frequencies.
Manufacturing the Tecnetron
It was necessary to develop special technical methods to manufacture the Tecnetron. This was one of the major achievements
of M. Teszner and the CNET researchers who aided him. For part of the work, the classic procedures of transistor production
could be followed. Then a whole series of new mechanical operations intervened: cutting the refined crystals into
plates, then into little rods. This last operation was performed with ultrasonic cutting apparatus. The constriction
for the neck was made by a procedure of electrolytic etching perfected especially for the purpose. The indium was
also deposited by electrolysis, with the rod in continuous rotation during the process. More conventional techniques
could be used in applying the terminal (cathode and anode) contacts.
Up to the present, procedures already developed permit manufacture on a large scale. Research is continuing, however,
and the next step is the creation of a power Tecnetron and another model especially for ultra-high frequencies. Special
arrangements which will permit continuing still further up the frequency spectrum are also under study. And, as always,
as the area of actual accomplishment is increased, the greater become the prospects of future progress.
* Publisher, Toute la Radio, Television, Radio Coustructeur et Deuarmeur, Eleetronique Industrielle
1 M. Teszner, Revue Génèrale d' Electricité, June, 1954.