Electronics World articles Popular Electronics articles QST articles Radio & TV News articles Radio-Craft articles Radio-Electronics articles Short Wave Craft articles Wireless World articles Google Search of RF Cafe website Sitemap Electronics Equations Mathematics Equations Equations physics Manufacturers & distributors Engineer Jobs Twitter LinkedIn Crosswords Engineering Humor Kirt's Cogitations Engineering Event Calendar RF Engineering Quizzes USAF radar shop Notable Quotes App Notes Calculators Education Engineering Magazines RF Cafe Software,T-Shirts,Coffee Mugs Engineering magazine articles Engineering software Engineering smorgasbord RF Cafe Archives RF Cascade Workbook 2018 RF Stencils for Visio RF & EE Shapes for Word Advertising RF Cafe Homepage Sudoku puzzles Facebook Test notes Thank you for visiting RF Cafe!
MECA Electronics

RCA Victor Portable Table Electrola Model R-95
Radio Service Data Sheet
July 1936 Radio-Craft

July 1936 Radio-Craft

July 1936 Radio Craft Cover - RF Cafe[Table of Contents]

Wax nostalgic about and learn from the history of early electronics. See articles from Radio-Craft, published 1929 - 1953. All copyrights are hereby acknowledged.

At least for now, I am going to only scan and post schematics & parts lists like this one featuring the RCA Victor Portable Table Electrola Model R-95 radio in graphical format, rather than run OCR on them to separate the textual content. There are still many people who restore and service these vintage radios, and often it can be difficult or impossible to find schematics and/or tuning information. I will keep a running list of all data sheets to facilitate a search.

RCA Victor Portable Table Electrola Model R-95
Radio Service Data Sheet

(Synchronous motor; takes records up to 12 ins.; pickup and tone arm in 1 unit; 8 in. dynamic speaker.)

RCA Victor Portable Table Electrola Model R-95 Radio Service Data Sheet, July 1936 Radio-Craft - RF Cafe

The voltages on the illustration at the left are measured from the tube socket terminal to the negative side of the electrolytic condensers. Voltages should be within ± 2.0%, as measured on a 1,000 ohm-per-volt meter. Values over 50 V. should be read On the 250 V. scale, while those under are taken from the 50 V. scale. Since a voltage-doubling circuit is employed in this instrument, it cannot be used on D.C. The power consumption is 75 W. total and the power output is 2. W. Turntable speed is standard 78 r.p.m. The motor is started by giving it a clockwise spin with the hand. Difficult starting may be cured in many cases by applying a small amount of oil to the bearing surfaces of the motor. A small amount of hum when the motor is starting, decreasing to a negligible amount when running is entirely normal. If there is excessive vibration either when starting or running, the motor supports should be examined and the position of the leather washer on the center bearing should be checked. It should be under the steel washer. After a long period of operation, the spacer cushions of the pickup may become hard and should be replaced. The viscoloid block which is attached to the front end of the armature shank serves as a mechanical filter to eliminate undesirable resonance and to cause a uniform frequency response. If the block is replaced it will be necessary to heat the shaft slightly to hold it firmly to the viscoloid block.

 

 

Posted August 27, 2015

Radio Service Data Sheets

These schematics, tuning instructions, and other data are reproduced from my collection of vintage radio and electronics magazines. As back in the era, similar schematic and service info was available for purchase from sources such as SAMS Photofacts, but these printings were a no-cost bonus for readers. There are 220 Radio Service Data Sheets as of February 2, 2018.

Windfreak Technologies Rohde & Schwarz FPC1500 Spectrum Analyzer - RF Cafe
Rohde & Schwarz USA (RF Component Pocket Guide) - RF Cafe Antenna Test Lab - RF Cafe
About RF Cafe
Kirt Blattenberger - RF Cafe Webmaster
Copyright: 1996 - 2018
Webmaster:
    Kirt Blattenberger,
    BSEE - KB3UON

RF Cafe began life in 1996 as "RF Tools" in an AOL screen name web space totaling 2 MB. Its primary purpose was to provide me with ready access to commonly needed formulas and reference material while performing my work as an RF system and circuit design engineer. The Internet was still largely an unknown entity at the time and not much was available in the form of WYSIWYG ...

All trademarks, copyrights, patents, and other rights of ownership to images and text used on the RF Cafe website are hereby acknowledged.

My Hobby Website:  AirplanesAndRockets.com

spacer