March 1958 Popular Electronics
Wax nostalgic about and learn from the history of early electronics. See articles
published October 1954 - April 1985. All copyrights are hereby acknowledged.
In March of 1958 when this article appeared in
Popular Electronics, learning of semiconductor devices other than transistors was usually new to experienced
professionals as well as to hobbyists. Vacuum tubes still dominated electronic products in the day.
Companies like General Electric, Sylvania, and RCA were the pioneers for development of Zener diodes,
photodiodes, SCRs, thyristors, etc. Exotic compounds like selenium, germanium, silicon, and lead and
cadmium sulphides were used. This article discusses some of those devices.
See other "Transistor Topics" in the series:
By Lou Garner
The use of semiconductor
devices other than transistors is expanding rapidly. Such devices bear approximately the same relationship
to the transistor that industrial control tubes, thyratrons, heavy-duty rectifiers, phototubes, and
gaseous voltage regulators bear to the vacuum tube.
Small diode detectors and semiconductor power rectifiers have been used for years - even before the
invention of the transistor. In addition, many special-purpose semiconductor diodes are either in current
production or are being developed. Available units include diodes designed to operate at the Zener point
as voltage regulators, and light-sensitive photodiodes.
The Zener diode is operated with a voltage applied in its reverse (or high-resistance) direction
at or very near to its nominal "breakdown" (Zener) voltage. When the applied voltage increases slightly,
the diode's resistance suddenly drops from a moderately high to a very low value. In conjunction with
a fixed series resistor, such units can serve as effective voltage regulators and are similar in operation
and application to the "VR" series of gas-filled voltage regulator tubes.
Photodiodes are made in a variety of styles and types. Virtually all types of semiconductor materials
are used in their construction, including selenium, germanium, silicon, and lead and cadmium sulphides.
They range in size from Sylvania's minute 1N77A, a germanium photocell smaller than a matchstick, to
the large selenium "sun batteries" manufactured by International Rectifier Corp.
Even General Electric Co.'s Unijunction transistor is, in reality, a special-purpose semiconductor
device rather than a conventional transistor. Originally called a "double-base diode," it has characteristics
roughly like those of a small gas-filled thyratron tube. G.E. is also developing a special silicon-controlled
rectifier which may serve as a possible replacement for both power relays and medium-sized thyratrons.
devices currently being produced by General Electric Co. include low-current silicon rectifiers
(above, right), and a silicon double-based diode (right, compared in size with Life Savers). The tab
protruding from the cap of the diode serves as a ground for shielding purposes.
diodes, such as these 1, and 3.5-watt units available from International Rectifier Corp., make
effective voltage regulators.
Fig. 1. Jack Yundt's
"Handy Audi" test instrument adapted from POP'tronics circuit.
Fig. 2. Ronald
Wilensky's simple field strength meter described fully in the article.
In fact, almost all semiconductor manufacturers are designing and developing new solid-state devices
to replace standard thermionic tubes. RCA, for example, is working on a "Thyristor," which may be operated
either as a bi-stable switching element or as a conventional high-frequency transistor.
Shockley's new "Bistable" diode is a four-layer silicon device having alternate layers of n-type
and p-type materials. When a control voltage is applied to its two electrodes, it can be switched from
a high-impedance state with a resistance of from 1 to 100 megohms to a low-impedance state with a resistance
of less than 20 ohms. In this respect, its action is much like that of a small neon bulb. It can be
used in similar applications, for example, in a saw-tooth oscillator or pulse generator.
As designers and engineers learn more about solid-state physics, you can expect to see more new semiconductor
Readers' Circuits. While a good many home experimenters like to work on and to experiment
with original circuits, a high percentage prefer to adapt "standard" circuits they have seen in magazine
articles and books to their own requirements. Often, this takes as much ingenuity and skill as is required
to "dream up" a new circuit. This month we are featuring a pair of interesting circuits which our readers
have adapted to their own needs.
Handy Audi. S/Sgt. Jack W. Yundt (AF 14504821, 45 Ftr. Day. Sq., Box 473, APO 117, New York, N. Y.)
is, to use his own words, "an amplifier tinker." When he saw Transtopic Experiment No. 15 in the February
1957 issue of POP'tronics (page 85), he decided to turn the original circuit (a simple code practice
oscillator) into a multi-purpose audio test instrument. He dubbed his completed test gadget "Handy Audi"
(see Fig. 1).
It can be used as: (a) a code practice oscillator (CPO) with loudspeaker output, (b) a CPO with headphone
output, (c) an audible tone source, and (d) an audio test signal source.
In operation, a single n-p-n transistor is used as a common-emitter audio oscillator, with transformer
T1 serving both to provide the feedback necessary to start and sustain oscillation and to match the
transistor to a loudspeaker's low-impedance voice coil. The feedback signal obtained from the transformer
is coupled back to the transistor's base electrode through d.c. blocking capacitor C1. Base bias current
is supplied through R1 and R2. Unbypassed emitter resistor R3 serves to stabilize circuit operation.
Operating power is supplied by a 9-volt battery, B1, controlled by s.p.s.t. on-off switch 81. The other
components and switches permit the circuit's operation to be modified for special applications.
All components used are standard and should be readily available. R1 is a small potentiometer - its
taper is not critical. R2 and R3 are 1/2-watt resistors. C1 can be a tubular paper or miniature ceramic
capacitor. S1, S2, and S3 are s.p.s.t. toggle or slide switches, while S4 is a d.p.s.t. unit. T1 is
an Argonne Type AR-119 transistor output transformer. The PM loudspeaker can be a 3" to 6" unit with
a 3- or 4-ohm voice coil. J1 is a standard open circuit jack; BP1 and BP2 are binding posts. The power
supply battery, B1, can be a standard 9-volt transistor battery or 1 1/2-volt cells.
Sergeant Yundt assembled his unit in a plastic case about the size of a table-model a.c.-d.c. receiver.
Since neither lead dress nor circuit layout is critical, however, you can use any size of case you wish.
To use the completed instrument as a CPO with loudspeaker output, connect a hand key to binding posts
BP1 and BP2 and close switches S1 and S2. With the key depressed, adjust R1 for desired operation. If
headphone operation is preferred, a pair of electromagnetic headphones is plugged into jack J1, and
switch S3 is closed. Switch S2 is opened to silence the speaker.
For use as an audible tone source, the key may be removed. Switches S1, S2 and S4 are closed, With
this setup, a steady tone is obtained from the loudspeaker. This is handy for such purposes as checking
microphone placement in p.a. installations.
Finally, to operate the instrument as an audio signal source, a test probe (simply a shielded lead
with a 0.5-.μfd. d.c, blocking capacitor in series with the central "hot" lead) is plugged into jack
J1. Switch S2 is opened and switches S1, S3 and S4 closed. The audio signal obtained from the probe
can be used for signal injection tests of phonograph amplifiers, p.a. systems, intercoms or other types
of audio amplifiers, including the audio sections of radio and TV receivers.
Field Strength Meter. If, at first glance, the circuit in Fig. 2 looks somewhat like one of the simple
diode and transistor receiver circuits you've seen featured in past columns, don't be too surprised.
Actually, it is such a receiver, but Ronald Wilensky (KN2ZPV), of 920 East 17th St., Brooklyn, N. Y.,
has modified the basic circuit for use as an inexpensive field strength meter.
In operation, r.f. signals picked up by the antenna are selected by tuned circuit L1-C1 and coupled
to a 1N64 diode detector, CR1. C2 serves as an r.f. bypass capacitor, insuring that only the d.c. component
of the detected signal is fed to the base-emitter circuit of the p-n-p transistor. The transistor, in
turn, is used as a common-emitter d.c. amplifier, with its output indicated as a deflection on the 0-1
milliammeter. Operating power is supplied by a 4.5-volt battery, B1, controlled by the s.p.s.t. "power"
switch S1. Series rheostat R1 serves as a sensitivity control.
Using readily available components, construction is straightforward and should pose no problems.
For best results, Ron indicates that the instrument should be assembled in a plastic case. L1 and C1
are chosen to cover the frequency band of interest to the individual builder. For the 27.255-mc. R/C
band, Ron suggests that L1 be made up of 12 turns of #16 wire, wound on a coil form 5/8" in diameter
by 1" long. C1, in this case, can be a 25-μμfd. variable. The antenna's length may be varied to suit
individual requirements - Ron used a straightened piece of "coat hanger" wire.
Sun Batteries. Some time ago, we announced that the International Rectifier Corp.
(1521 East Grand Ave., El Segundo, Calif.) was planning to introduce a new series of inexpensive silicon
solar cells. These units are now in full production. They have an active area of about 0.78 square inch.
Mounted and unmounted styles are available in both "standard" and "selected" (optimum output) versions.
Prices range from $4.00 for an unmounted "standard" cell (Type No. SA5-PL) to $8.00 for a mounted "selected"
unit (Type No. SA5A-M). A standard cell can deliver over 20 milliwatts into a 4-ohm load with an illumination
of 5000 foot-candles. Its open circuit voltage at this light level is about 0.45 volt.
Product News. An important step towards the standardization of transistor types
has been taken by Raytheon and Tung-Sol Electric. Both of these firms are now producing several transistors
under the same EIA-registered type number.
Another new transistor manufacturer has entered the field-Fairchild Semi-Conductors Corp., Palo Alto,
Calif. This new firm is sponsored by the well-known Fairchild Camera and Instrument Corp. Present plans
call for the development and production of silicon diffused transistors and other semiconductor components.
Zenith and Philco are now producing fully transistorized portable short-wave receivers. Both are
multiband sets, and sell for well over two hundred dollars each.
RCA has introduced several new transistor types. The 2N404 is a p-n-p junction transistor designed
for use in switching circuits, has a maximum collector current rating of 100 ma., a maximum dissipation
of 120 mw., and an alpha cutoff frequency of 4 mc. The 2N408 is a p-n-p junction transistor intended
for Class A and Class B audio service in entertainment-type receivers; a pair of 2N408's in Class B
push-pull can deliver a 160-mw. output signal with a 9-volt power supply. The 2N407 is similar to the
2N408 except for basing.
Lansdale Tube Company, a division of Philco, has introduced a new series of MADT (Micro Alloy Diffused-base
Transistor) v.h.f. transistors. One of these units will serve as an oscillator up to 1000 mc.
That's the show for now, fellows. See you next month.
Posted August 13, 2012