Electronics World articles Popular Electronics articles QST articles Radio & TV News articles Radio-Craft articles Radio-Electronics articles Short Wave Craft articles Wireless World articles Google Search of RF Cafe website Sitemap Electronics Equations Mathematics Equations Equations physics Manufacturers & distributors Engineer Jobs LinkedIn Crosswords Engineering Humor Kirt's Cogitations Engineering Event Calendar RF Engineering Quizzes USAF radar shop Notable Quotes App Notes Calculators Education Engineering Magazines Engineering magazine articles Engineering software Engineering smorgasbord RF Cafe Archives RF Cascade Workbook 2018 RF Stencils for Visio RF & EE Shapes for Word Advertising RF Cafe Homepage Sudoku puzzles Thank you for visiting RF Cafe!
MECA Electronics Attenuators

The Possible Impractical Impossible Circuit
September 1967 Popular Electronics

September 1967 Popular Electronics

September 1967 Popular Electronics Cover - RF CafeTable of Contents

Wax nostalgic about and learn from the history of early electronics. See articles from Popular Electronics, published October 1954 - April 1985. All copyrights are hereby acknowledged.

Can a single diode be used to constitute a full-wave rectifier circuit? The short answer is yes, it can, as is demonstrated by an actual circuit built by Messrs. Duffy and Olesky. The real question is can a single-diode full-wave rectifier be used in a practical circuit? Under certain controlled instances it can as long as component values and tolerances for both the power supply and the load can be controlled acceptably. High impedance, ultra low current circuits in today's marketplace are more likely to be able to support the single-diode rectifier, but then so many products are composed of a single integrated circuit that can easily include an internal two- or four-diode full-wave bridge that such a money- and space-saving scheme is not necessary. Still, it is an interesting theoretical study.

The Possible Impractical Impossible Circuit

Would You Believe a Single-Diode Full-Wave Rectifier?

By Tom Duffy and Jerry Olesky

A one-diode full-wave rectifier? Impossible! Everyone knows you need at least two diodes for full-wave rectification. Or, should we say, everyone asĀ­sumes that you need two diodes.

You can demonstrate one-diode full-wave rectification with the circuit shown below, left. The frequency of the input is relatively unimportant. Connect an oscilloscope across output terminals D and C and you should get one of the three waveforms shown, depending upon the position of the potentiometer arm.

With the potentiometer arm at the top, the waveform should be like the one at the extreme left. Rotating the arm to the other extreme should produce a waveform like the one in the middle photo. If you carefully balance the two waveforms (via the potentiometer), the output should become a typical full-wave rectification pattern (right).

The two theory schematics (center and right) show what's happening. When terminal B is negative with respect to A, the current flow is indicated by the arrows. Note that current goes through the rectifier and through the load resistor. When the polarity of the input is reversed, current flow through the rectifier is blocked, but a new path is formed through resistor R1 and current continues to flow through the load. Thus, no matter what the sine-wave excursions are, the direction of flow through the load resistor is the same - hence, you have full-wave rectification.

Why isn't this circuit used in practical everyday equipment? Well, in a conventional full-wave rectifier the efficiency can go up to 90%, but in this one-diode arrangement the efficiency is only about 25%. Also, all of the resistors are in series with the load and any voltage drop across them will subtract from the output.

The Possible Impractical Impossible Circuit, September 1967 Popular Electronics - RF Cafe

(left) The test circuit diagram is shown below. You can easily duplicate this experiment as a science fair project. All of the scope photos above were taken off a Heathkit Model 10-14.

(middle) As potentiometer is rotated from one extreme to the other, traces show two different half-wave patterns (above left, and center).

(right) Balance the two half waves and the scope trace should look like the one above. The theory diagrams are shown below.

 

 

Posted September 24, 2018

Windfreak Technologies Triad RF Systems
Rohde & Schwarz USA (RF Component Pocket Guide) - RF Cafe Antenna Test Lab - RF Cafe
About RF Cafe
Kirt Blattenberger - RF Cafe Webmaster
Copyright: 1996 - 2018
Webmaster:
    Kirt Blattenberger,
    BSEE - KB3UON

RF Cafe began life in 1996 as "RF Tools" in an AOL screen name web space totaling 2 MB. Its primary purpose was to provide me with ready access to commonly needed formulas and reference material while performing my work as an RF system and circuit design engineer. The Internet was still largely an unknown entity at the time and not much was available in the form of WYSIWYG ...

All trademarks, copyrights, patents, and other rights of ownership to images and text used on the RF Cafe website are hereby acknowledged.

My Hobby Website:  AirplanesAndRockets.com

spacer