July 1963 Popular Electronics
Table of Contents
Wax nostalgic about and learn from the history of early electronics. See articles
published October 1954 - April 1985. All copyrights are hereby acknowledged.
"The boy and his father had just
witnessed a demonstration of one of the most promising and fastest developing technological
devices ever conceived by man - the laser. In only three whirlwind years, the laser -
which gets its name from the initials of Light Amplification by Stimulated Emission of
Radiation - has moved out of the theory stage, out of the laboratory curiosity category,
and into a whole new, exciting world of applications." That's the opening of an article
in the July 1963 edition of Popular Electronics. I remember when ruby lasers
were the the rule rather than the exception for lasers. Power levels were measured in
units of 'Gillettes' in reference in the number of razor blades they could cut through.
Next came chemical lasers with power levels in the megawatts and now even gigawatts that
can take out ICBM warheads as they reenter the atmosphere and fry orbiting satellites.
At the same time the realm of semiconductors and microcircuits was turning out devices
on the opposite scale for use in communications, inertial navigation, and boardroom presentation
pointers. This article is an extensive recounting in layman's terms the state of the
art in 1963.
The "Light" Fantastic
Laser Status Report
One development follows another in rapid succession
By Ed Nanas
The man behind the telescope-like device was ready.
"I'll count down so you won't miss the action," he said. "All set? Here we go - three,
two, one, FIRE!" A pencil-thin beam of red light shot out from a six-inch ruby rod less
than a half-inch in diameter. It smashed through a stainless steel plate as if the tough
metal wasn't even there. Then it hit a balloon suspended some ten feet away, vaporizing
the rubber. And still the beam of light continued on its narrow path, burning a small
hole in a curtain at the far end of the room. It was all over in a fraction of a second.
"Wow! That light sure packs a wallop!" exclaimed a teen-age radio amateur.
Rigth: A c.w. gas laser recently demonstrated by Sylvania. An r.f. field excites gas
mixture to self-sustaining oscillation.
He was standing at the rear of the hall with his father, an electronics engineer.
"I've never seen anything like it!"
Until three years ago, nobody had seen anything like it!
The boy and his father had just witnessed a demonstration of one of the most promising
and fastest developing technological devices ever conceived by man - the laser. In only
three whirlwind years, the laser - which gets its name from the initials of Light Amplification
by Stimulated Emission of Radiation - has moved out of the theory stage, out of the laboratory
curiosity category, and into a whole new, exciting world of applications.
The laser has the unique ability to generate and amplify light waves at specific wavelengths
just as radio waves are generated and amplified at specific wavelengths. Light generated
by a laser is known as coherent light because it is "pure," or predominantly of one frequency.
Making the sun seem like a hand-held flashlight by comparison, the thin beams of coherent
light, which have already vaporized steel and, in a recent experiment, illuminated the
moon, can be used to:
- Transmit a billion simultaneous telephone conversations on a single thread of light
one millimeter in diameter -without interference;
- Build laser radar systems, including portable range finders, having resolutions more
than 1000 times better than conventional narrow-beam radars;
- Perform micro-surgery - delicate eye surgery has already been demonstrated - precise
enough to allow cutting of a single human cell;
- Reach billions of miles into space with a beam powerful enough to guide a spaceship,
communicate with life on planets in other solar systems;
- Construct ultra-precise clocks, guidance systems, and laboratory instruments;
- Devise practical underwater communications and ranging systems using recently developed
techniques for generating green or blue coherent light;
- Build new battlefield weapons, including an anti-missile device and a form of "death
- Greatly speed up the functioning of complex computers by using lasers in conjunction
with fiber optic paths to transmit great masses of information within a computer or from
one machine to another;
- Investigate the possibility of transmitting electric power through space;
- Speed up chemical processes thousands of times, such as those that take place during
Fantastic? Not at all; and the list is by no means complete. The laser is indeed creating
a revolution, and new discoveries relating to the generation and application of coherent
light are being announced almost daily. Let's take a closer look at the phenomenon of
laser light and the mechanisms used to generate it.
TV via laser is an accomplished fact. Image
of the young lady is relayed (in this experiment) to an optical modulator which impresses
it on a c.w. laser beam. The beam strikes a photocell in a telescope-like receiver (right,
rear) and is converted to the TV signal seen on monitor.
Highest power laser to date, the 350-joule Raytheon
model below may soon be dwarfed by powers as high as 3000 joules. Intense beam of light
is shown blasting its way through a steel girder a quarter-inch thick.
Continuous wave (c.w.) lasers have reached
powers of 9 watts and are expected to go higher in the near future. Many of these types
use a dysprosium-doped calcium fluoride crystal as does the RCA model below. The whole
apparatus is enclosed by two hemispherical mirrors which focus light on the crystal.
The crystal itself is obscured by the light source next to it.
Sunlight pumping of a solid-state laser is
a new development which may soon make it possible to put sun-powered laser aboard satellites
for communications, tracking, and geodetic measurements. This device, designed by RCA,
uses a 12" hemispherical mirror to focus sun on calcium fluoride crystal rod.
Laser rifle is actually a compact rangefinder
which fires a pulse of coherent light, collects the light reflected back from the target,
and indicates exact distance to the target by computing the elapsed time for pulse's
round trip. The device has measured up to seven miles.
A "Colidar" (for Coherent Light Detecting
and Ranging), produced by Hughes Aircraft Co., operates on the same principle as the
laser "rifle" opposite. Research is underway on other laser ranging devices.
Brightest stars of recent research are semiconductor and liquid laser devices.
Liquid "frequency converter" that can change
the frequency or color of a laser beam.
One of the first gallium arsenide lasers
produced by G.E. (others were made by I.B.M. and M.I.T.). It is suspended in liquid nitrogen
to keep it cool when large excitation currents are passed through it.
I.B.M scientists examine a brand-new semiconductor
laser announced very recently: an indium phosphide type.
Coherent vs. Incoherent. Light waves coming from the sun or from
incandescent or fluorescent lamps consist of a broad band of frequencies all mixed together.
In addition, light from these sources can be considered as having been emitted from an
infinite number of sources, all of which have random phases and polarizations with respect
to one another. We call this kind of light incoherent.
A similar thing happens in the radio bands when lightning is discharged. A whole host
of frequencies are generated, and they can be heard as noise or static on a radio receiver.
As another example, incoherent water waves on the surface of a pond can be created by
throwing in a handful of pebbles; coherent waves by dropping in a single large size rock.
Both a radio transmitter and a laser generate coherent radiation that is predominantly
of one specific frequency. The difference between the two is that the radiation produced
by the laser is very much higher in frequency (and, therefore, much shorter in wavelength),
so that it falls within the optical portion of the electromagnetic spectrum.
The electromagnetic spectrum ranges from extremely low frequencies where wavelengths
(the distance between two specific crests or two troughs in a given wave) can be measured
in miles or meters, to frequencies far above the visible band where wavelengths are measured
in microns (one-thousandth of a millimeter) and angstrom units (one ten-thousandth of
a micron). In terms of cycles per second, light waves vibrate at an extremely rapid rate
- 1015 cps would be a rough figure.
t visible frequencies, radiation must be generated on an atomic level - as in a laser.
This is made possible by the fact that the atoms of certain materials, when excited by
large doses of energy, emit light at one frequency or group of frequencies. Thus, a substance
(ruby, for example) made up of atoms which can be excited, and which will, at a certain
point, emit coherent light, are used in lasers instead of the electron tubes used at
The Amazing Laser. The properties exhibited by laser beams are much
more startling than the foregoing explanation indicates. Like ordinary light, they can
be focused and modulated, but there the similarity ends. A laser beam, because of its
extremely short wavelength and because it is generated at the atomic level with all of
the light energy in phase, is a very narrow beam of extremely high energy. This energy,
concentrated at a single point, can burn through steel.
The fact that a laser beam can be modulated is expected to be of great importance
in future applications. The reason is easy to understand. The transmission of a voice
by radio requires a band of frequencies several thousands of cycles wide. The transmission
of a television signal complete with sound takes up six million cycles of the available
spectrum. By and large, the radio portion of the spectrum is now overcrowded, and the
situation is expected to get progressively worse.
The use of optical frequencies for communications opens up great new vistas. In the
visible white-light portion of the spectrum alone, the number of frequencies available
is fantastic - 250 million megacycles! This figure represents thousands of times more
frequency space than in all the radio frequency bands combined. One or two laser beams,
relayed as microwaves are now, could carry all of the communications traffic in America
from coast to coast - telephone calls, television programs, computer data, and facsimile!
Optical Powerhouses. The first successful pulsed optical maser (laser)
generated a peak power of about 10 kilowatts for very short intervals. The newer lasers
have now climbed much higher - recently one was announced by the Korad Corporation with
a peak of 500 megawatts (500,000,000 watts) - all concentrated in one narrow beam of
7-nanosecond duration. For the 500-megawatt pulse, it was calculated that the electric
field in the focused electromagnetic beam was on the order of 107 volts per
centimeter. The beam was observed
to cause ionization of the air in its focal path
with a brilliant blue flash, and spectacular damage was done to materials placed at the
focal point. Since these gigantic pulses of energy were for extremely short intervals,
the total pulse energy was only about 5 joules.
In only one year, the output energies of pulsed lasers have spiraled up from 1 or
2 joules (one watt for one second) to 350 joules. A thousand joules is just around the
corner and may be achieved by the time you read this. A glass laser with a pulsed output
of somewhere between 2000 and 3000 joules is under development by American Optical Company,
and may be announced as early as August, 1963. Theoretically, there is no limit. Ten-thousand-joule-outputs
are predicted within the next year.
What do all these figures mean? Just one joule - about the same amount of energy you
get from a flashlight bulb in several seconds of operation - is enough to vaporize a
hole through a 1/32-inch-thick sheet of steel if it is transmitted in a concentrated
burst of about a millisecond.
A 10-joule ruby laser, which is fairly common today, operating at a wavelength of
0.7 micron, has a power density at the center of the beam of about 1016 watts
per square meter. The power density at the surface of the sun is less than 108
watts per square meter. Thus, this rather modest laser is capable of producing a power
density 100-million times that of the surface of the sun!
THE BASIC LASER
The essential ingredients of a laser are:
A resonant cavity: Usually formed by two reflecting surfaces, such
as precisely parallel mirrors, one slightly less opaque than the other;
An active medium: Positioned inside the cavity with its axis perpendicular
to the reflecting surfaces. It may be a (1) gas-a noble gas such as helium, mixed with
neon, and contained in a glass or a quartz tube; (2) crystal-a rod of high purity ruby,
glass or a rare earth material such as calcium tungstate; (3) liquid-an organic liquid,
such as benzene or pyradine; (4) semiconductor-the newest of the lasers, a gallium-arsenide
Pumping power: Applied to the active medium to excite its atoms.
It may consist of: (1) high-power lamps - used with crystal lasers; (2) concentrated
sunlight - also used with crystal lasers; (3) electrical or radio frequency discharge
- used with gas lasers; (4) direct electric current - 10,000 to 20,000 amperes injected
directly into the junction of a diode laser.
The basic principles of laser light generation are similar to those of the microwave
maser. Atoms in the active medium can possess different amounts of energy. Ordinarily,
an atom will occupy the lowest of several energy levels, and is said to be in the ground
state. But when "pumping" power is applied, they get excited. That is, the atoms absorb
some of the photons (particles or "quanta" of light) from the power source and jump to
a higher energy level, like water being pumped into a tank atop a standpipe.
At this higher energy level, usually two steps above the ground state, the atoms begin
to relax. They fall to an intermediate energy level, but still above the original lowest
level. This intermediate level is called the metastable condition, because the atoms
are more reluctant to leave it than they were to leave the higher level to which they
were originally excited. In order to make their departure they must give up the light
they absorbed. The important thing is that the light they give up in dropping back to
the ground state is of a specific wavelength.
Sooner or later, (within a few microseconds), the first atoms begin to drop from the
metastable level. They are put to work in the resonant cavity of the laser. Without the
reflecting surfaces, the light they emit would be mere fluorescence, like that of a neon
sign. But inside the resonant cavity of the laser, they are bounced back and forth. With
each pass parallel to the axis of the active material, they stimulate other excited atoms
in the metastable level to give off their absorbed light much more quickly than they
would ordinarily. The stimulated light moves in the same direction as the light stimulates
it. With each pass, the light gains more energy in an effect akin to a chain reaction.
In only 200 microseconds or so, the released light waves, traveling in parallel and
in phase back and forth between the reflecting ends of the laser - you might call it
"feedback" - build up to an intensity great enough to escape through the one end of the
laser which is only partially opaque. This output beam of light has, .most all of its
intensity In a very narrow cone. All its waves are in step; of the same phase and frequency,
It is coherent light.
Basic configuration of a low-power c.w. gas laser. The reflecting plates reflect back
a large percentage of energy; result is a small, continuous output.
Continuous-Wave Lasers. A little over a year ago, the first crystal
laser was made to operate continuously (the high-power devices we have been discussing
are pulsed) at Bell Laboratories with power outputs of a few milliwatts. Gas lasers and
semiconductor lasers also have been made to operate continuously with comparative power
outputs. As POPULAR ELECTRONICS goes to press, however, a new 9-watt continuous-wave
(c.w.) laser is about to be introduced for use in research related to welding and other
machine tool uses.
A 45-watt c.w. laser may be another major development to be announced in 1963. Both
this unit, which is being researched at M.I.T.'s Lincoln Laboratory, and the 9-watt c.w.
laser use dysprosium-doped calcium fluoride crystals rather than gases or semiconductors.
Although c.w. lasers are somewhat puny in their power outputs compared to the pulsed
type, they have immense advantages as carriers for communications purposes. At optical
frequencies and with narrow beam angles concentrating all the radiated energy into a
small cone, a television channel could be established between the earth and Saturn with
only about 600 watts, while a voice channel to the most distant planet, Pluto, could
be maintained with as little as five watts.
Dr. Donald S. Bayley, of General Precision, Inc., one of some 400 organizations conducting
laser research, has said that an interstellar information channel carrying one binary
bit per second could be set up with the star Altair (16.5 light-years away) with only
10 watts from a laser. Already, General Electric has designed a burst communications
system using a rapid laser pulse of great power (rather than a continuous wave) to carry
vast amounts of data.
LASER STATUS REPORT
Gallium arsenide laser, greatly enlarged and shown in schematic form,
looks like this. Coherent light is emitted perpendicular to the front and back surfaces
and along the junction of device.
Power Transmitters? In the vacuum of space, attenuation is slight,
governed primarily by the degree of beam spread. Recently, Sperry Rand Corporation has
been able to achieve the minimum theoretical beam spread of a point source of light -0.005°,
or 10-4 radians - without the use of external lenses. Previously, the already
narrow laser beams, on the order of 0.05°, were further focused down by what amounts
to an inverted telescope.
The ultra-small beam spread of concentrated optical-frequency energy indicates that
it will be possible to transmit power over great distances with very little loss; power
for spaceships, for instance. It is now possible to construct optical antennas, nothing
more than a series of lenses, to transmit laser beams which would lose only 1/30th of
one percent in a 20-mile hop - far less than present-day transmission lines. Thus, if
you had a laser putting out one million watts, a hundred miles away you would receive
997,500 watts: still quite a bit of power.
Laser Radar. One of the immediately attainable applications of the
laser is in a radar-like system for measuring distance and velocity, and for tracking.
Several such systems already have been built or are in the works, including those of
Hughes, RCA, General Electric, and Sperry. For example, the RCA tracking system, using
a two-inch corner reflector, is expected to achieve a range accuracy of six feet over
70 miles. The Sperry system, using the Doppler effect, can measure the frequency shift
of vehicles traveling at 18,000 miles per hour, or as slowly as 0.2-inch per hour!
Such systems on the moon or in a satellite hold tremendous promise for guiding spacecraft
and rendezvousing in space. By 1965, laser radars are expected to provide high-resolution
maps of the moon and Mars, yielding new information about their surfaces that will make
landing a man a fairly safe procedure. A laser ranging and telescope system will go into
operation this year at Cloudcroft, N. M., to track satellites such as the new Discoverer
series; in that area of the country, the weather is generally clear and lasers can be
beamed into space from the ground.
Even the heavy-wheel gyroscope may be on its way out as a result of laser technology.
Sperry Gyroscope - the organization which invented the gyro - has come up with a closed-circuit
ring of lasers which can be used as an automatic device for guiding ships, planes, missiles
and space vehicles.
New laser Types. One of the most important developments in the rapidly
changing field of laser technology came late last year when three organizations, I.B.M.,
General Electric, and M.IT., announced almost simultaneously the development of a semiconductor
The advantages of this type of laser-a gallium arsenide (GaAs) diode - are impressive
when compared to crystal and gas lasers. Semiconductor lasers approach efficiencies of
100 percent as compared to a few percent for other types; they are excited directly by
electric current while other lasers require bulky optical pumping apparatus; because
they are excited by an electric current, they can be easily modulated by simply varying
the excitation current.
Gallium arsenide diodes (research models are already available as relatively low-cost,
off-the-shelf items) consist of a layer of p-type gallium arsenide and a layer of n-type
gallium arsenide. When electrons in an intense electric current, about 20,000 amperes
per square centimeter, are applied to the device, it emits coherent or incoherent light,
depending upon the diode type, from the junction between the two layers of gallium arsenide.
Current research is concerned with improving the efficiency of semiconductor lasers,
modulating them, and, in a new twist, using them as "pumps" to improve greatly the efficiency
of other types of lasers.
Developed in a number of forms are lasers which use rare earth chelates - molecules
which completely enclose each atom of a rare earth element such as europium. Chelates,
combined with plastic, a liquid or other medium, can be pumped to produce laser action.
One of the most important new laser techniques is a method for generating light of
different frequencies or colors from a single laser beam. By beaming coherent light through
a liquid such as nitrogen, light of other frequencies is obtained. Laser frequencies
can also be altered by heterodyning two beams by mixing them within a crystal. These
developments make it possible to convert intense laser beams to any frequency; green,
blue, or from far infrared to near ultraviolet regions.
Also within the year we have seen lasers operating at room temperatures rather than
having to be immersed in expensive cryogenic environments to keep them cool. Lasers pumped
by the sun, by cathode-ray fluorescence, and by exploding wires, as well as by directly
applied electric current, have come into being in the past twelve months. Raytheon and
M.IT. have bounced a laser beam off the moon. Whereas early last year you had to build
your own laser if you wanted one - an expensive and delicate process even for the most
advanced electronics engineer-you can now buy a wide variety of laser types.
Continuous wave crystal lasers use configurations somewhat
like this Bell telephone design. The neodymium crystal is at one focus of a elliptical
cavity, and the mercury lamp at the other to concentrate pumping light.
The Modulation Problem. While predictions on the future usefulness
of laser beams in communications are highly optimistic, much work remains to be done
on developing practical methods of modulation. Communications - including television
signals - have already been transmitted by laser in laboratory setups, but thus far,
only a small fraction of the fantastically large available bandwidth in a laser beam
has been utilized.
The various approaches to modulation can be divided into two groups: internal modulation
applied while the coherent light is being generated, and external modulation applied
to the light beam after it leaves the laser. As we noted earlier, the gallium arsenide
laser is relatively easy to modulate using an internal technique. The excitation current
can be simply varied to produce modulation.
Another method of internal modulation, used with other types of lasers, involves changing
the Q of the laser cavity with an electro-optical shutter between the laser material
and a reflecting end plate of the cavity. This introduces a variable loss which causes
large changes in the level of operating power akin to amplitude modulation.
A third approach is Stark-effect modulation, achieved by sending a strong transverse
electric field into the laser material. This field causes line-splitting and frequency
modulation of the output. A similar technique, using a magnetic field, has also been
used. It is called Zeeman-effect modulation.
External modulation of the laser output can be accomplished using the Pockels effect,
in which the beam is passed through a piezoelectric crystal which can be "strained" by
an electrical field. Other external modulation approaches include the Kerr effect (plane-polarization),
varying the pumping power, and mechanical means, such as the use of shutters, graings,
lenses, reflectors and ultrasonics.
For demodulation, the radiation must be converted
to electrical energy in most cases. New phototubes, photomultiplier detectors, and photodiodes
have been developed for this purpose within the last six months. With coherent radiation,
the same techniques will work with light beams that will work with microwaves, so it
boils down to a difference in detail, not principle. Superheterodyne techniques can be
used to convert the light into lower frequency signals, such as microwaves; microwave
detection equipment can then be employed. "Heterodyning" is accomplished by "beating"
one laser beam with another. The result is a frequency equal to the difference between
the two falling in the microwave region.
Lasers, Present and Future. As indicated earlier, it isn't only the
communications people who are taking a close look at the laser. At Columbia-Presbyterian
Medical Center in New York, ophthalmologists already have used a ruby laser beam to coagulate
a human eye retina to prevent it from becoming detached. Such an operation can be completed
in less than 0.001 second, eliminating the possibility of damage due to eye motion during
The machining and welding potential of the laser has already been demonstrated in
certain applications. At G.E., the surfaces of industrial diamonds have been vaporized
the instant the high-energy light beam strikes them. Production lines are now being set
up to use the laser beam in cutting "components" to size for use in microcircuits, and
to weld leads to semiconductors.
The laser also holds the potential of becoming the ultimate anti-missile weapon. One
proposal is to use high-power beams of several lasers focused on the enemy missile with
sufficient energy to vaporize it. This would be a "clean" weapon compared to anti-missile
rockets with nuclear warheads and their attendant radioactive fall-out.
A new laser scheme which theoretically could generate a billion joules or more is
under development now. It involves the separation and sorting of hydrogen spins, the
physics of which are too complex to go into in this article. Such a powerful laser could
transmit its beam through the atmosphere and earth cloud cover and still deliver enough
power at the impact point to vaporize a missile.
Power requirements could be sharply reduced, however, by orbiting an anti-missile
laser above the atmosphere. Laser light could also be used as a spotlight from space
for photography at long distances.
The laser is less than three years old, yet we have already come a long way. The experts
say that this is one field in which we are well ahead of the Russians. To understand
the laser is to understand an important facet of the future of communications, medicine,
machining for industry, and the practical equivalent of the legendary death ray.
Whatever use the laser is put to, its impact on mankind will be great-comparable,
perhaps, to the discovery of atomic energy. When and how will the impact be felt? Only
time will tell.
Posted January 16, 2013