May 1961 Electronics World
Table of Contents
Wax nostalgic about and learn from the history of early electronics. See articles
Electronics World, published May 1959
- December 1971. All copyrights hereby acknowledged.
My first experience with negative resistance was when an engineer I worked for at Westinghouse Electric, in Annapolis,
Maryland, used a tunnel diode to design a simple oscillator circuit. The project we were working on required an absolute
minimum number of parts, with everything implemented using bare die on a custom polyimide substrate printed circuit
board. I did the assembly, wire bonding, and encapsulation, and often initial test. Mr. Rufus Turner does a nice job of
briefly covering the history and application of negative resistance devices; tunnel diodes were not the first.
See author's "A.C.
Negative-Resistance Devices" article in the July 1963 Electronics World.
Negative Resistance - What It Is & How It's Used
By Rufus P. Turner
Negative-resistance devices have been with us long before the tunnel diode. Here are descriptions of some of them, along
with how and why they operate.
The tunnel diode has turned many minds toward negative resistance for the first time. Negative resistance is not new,
but some electronics people just a few years ago had not heard of the phenomenon, or had forgotten what they once learned
about it, because they would give a pitched battle on the subject. Always, they challenged, "How can you make any resistance
lower than zero?", which only shows that they thought in terms of wiping out resistance, not of changing its sign. Zero
resistance is one thing; while negative resistance is something else again.
Fig. 1 - Illustration of basic negative resistance principle.
Fig. 2 - Negative-resistance E-I curves.
The concept is easily demonstrated to the dubious, in the following common-sense terms. Consider a negative resistance
(Rn) connected in series with a conventional (positive) resistance (R) and an adjustable d.c. source (E), as
shown in Fig. 1. The following facts are evident: (1) the same current, I, flows through all parts of this series circuit
and is determined by the voltage E and the sum of the two resistances (without regard to the negativity of (Rn),
so Ohm's Law is not violated. The interesting point is what happens to the voltage drops, e and en, produced
by this current: whereas e increases with E and I in the normal manner, en decreases. (Increase I, and en
decreases; decrease I, and en increases.) Thus, the EI curve of this component must have a negative slope. (2)
Irrespective of their magnitudes, however, e + en =E. So Kirchhoff's Second Law is not violated. (3) Whereas
the conventional resistance consumes power, the negative resistance seems to deliver power. Actually, the total power supplied
by the d.c. source remains the same; it is only distributed differently between the positive and negative resistances. Thus,
the Law of Conservation of Energy is not violated.
Most negative-resistance devices have a current or voltage region in which their resistance becomes negative. Outside
of this region, the resistance may be positive. In Fig. 2A, for example, as current through the device is increased, the
voltage drop across the device increases from 0 to A, indicating positive resistance, but then decreases from A to B as
the current is further increased, indicating negative resistance. In Fig. 2B, there is a negative-resistance region (AB)
between two positive-resistance regions (OA and BC). Thus, at voltage Ex device current may have anyone three
values (I1, I2, or I3). Another type of negative-resistance device would have the current
and voltage axes swapped. Positive-resistance regions are negative-resistance regions unstable.
Negative resistance may be put to work for various tasks, such as oscillation, amplification, frequency conversion, harmonic
generation, counting, and switching. The circuits usually are very simple, since the negative resistor generally is a 2-terminal
device. Fig. 3 shows several typical circuits. A rule of thumb is that when a negative resistance (Rn) is operated
from a d.c. supply in series with a positive resistance (R), shunting Rn with a capacitor (as in Fig. 3A) produces
a relaxation oscillator, and shunting it with an LC tuned circuit (Fig. 3B) produces a sinusoidal oscillator. Fig. 3C shows
one of many negative-resistance amplifier circuits. Here, the d.c. voltage, Ed.c., biases the negative resistor,
Rn, into its negative-resistance region, the a.c. signal is supplied by a generator having internal resistance
Rg, and the output signal is developed across the load resistance, RL If Rn were not in
the circuit, EL would equal EgRL (Rg + RL). With Rn present,
however, operation is somewhat different. In this case, the gain increases so that the amplifier may go into oscillation.
Here the negative resistance is simulated by the use of positive or regenerative feedback.
Fig. 3 - Equivalent circuits of negative-resistance devices. Circuits simulated are (A) relaxation oscillator,
(B) sinusoidal oscillator, (C) amplifier, (D) flip-flop.
Fig. 4 - The arc-converter transmitter.
Fig. 5 - The early split-anode magnetron.
Fig. 6 - Circuit and curve for the dynatron.
Fig. 7 - Grounded-grid amplifier application.
Fig. 8 - Point-contact transistor operation.
Fig. 9 - The junction-transistor duo circuit.
Fig. 10 - Uni-junction transistor circuit.
Fig. 11 - Point-contact germanium diode circuit.
Fig. 12 - Circuit showing use of thermistor.
Flip-flop action may be obtained when a negative resistor is operated so as to provide three-point response, such as
shown in Fig. 2B. The device is initially biased at its lowest EI point (I1 the first stable state in Fig. 2B).
If the voltage then is raised momentarily higher than the value Ex, the device conduction will flip to the second
stable state (I3 in Fig. 2B), where it will remain until switched back to I1 or until the bias is
momentarily interrupted. Fig. 3D shows a two-legged circuit (with two negative resistors, Rn1 and Rn2)
employing this principle. First, Rn1 in one leg conducts at the low point (I1 in Fig. 2B) and Rn2
in the other leg is at point I3 in Fig. 2B. Momentary increase of the bias by application of the trigger pulse
shifts Rn1 to point I3. But because of the voltage drop across the common series resistor, R1
both legs cannot be maintained "on" i.e., at conduction point I3) simultaneously. So Rn2 switches
"off" (i.e., to point I1. Thus, alternate trigger pulses switch the output back and forth between Output 1 and
The tunnel diode is a simple, convenient, and practical negative-resistance device but it is not the first component
to provide -R. The answer to the question, "When were you ever able to buy a negative resistor?" is "For a long time, indeed,
but it was called by other names; negative resistance was not its main function." Devices which exhibit negative resistance
have come forward from the early days of wireless to the present time, and it seems likely that new ones will be discovered
long after the tunnel diode has become commonplace. The following discussion describes a few of the most prominent devices
other than the tunnel diode. Only d.c.-operated devices are included.
Arc. In 1900, Dudell discovered oscillation in the d.c. electric arc, and Poulsen soon put this device to work as a generator
of continuous waves which finally actualized early radiotelephony. (The arc must not be confused with the spark transmitter,
which generates damped waves.)
Fig. 4 shows the basic circuit of an arc transmitter. To increase efficiency, the arc was operated in a hydrocarbon atmosphere;
and, for good heat conduction, one electrode was made of copper. The applied voltage was from 200 volts to several kilovolts
d.c. and power ratings extended up to 1000 kilowatts. In the 1920's, many of the high-powered government radio stations
were arc-equipped. Long wavelengths were used. The arc gave way to the more efficient and compact, clean-operating vacuum
tube but it is important historically as an early, high-powered, negative-resistance device.
Magnetron. The magnetron (first reported in 1921) is a vacuum diode tube in which negative resistance can be obtained
through the action of electrons in a strong field produced parallel to the tube electrodes by an external permanent magnet.
Fig. 5 shows one type of magnetron. Here, the anode (plate) of the tube is split into two halves. Electrons tend to pass
from the filament or cathode to both halves of the anode; but actually pass in the greater number (producing high current)
to the half which is at the lower potential. This effect of increasing anode current by lowering anode voltage corresponds
to negative resistance. This type of magnetron is used up to 1000 mc.; other types at higher microwave frequencies.
Dynatron. Another old-timer (1918) is the dynatron effect in tetrode vacuum tubes. Fig. 6A shows a typical dynatron oscillator
circuit. In this arrangement, the tube screen is operated at a higher positive voltage than the plate. Secondary emission
from the plate is responsible for the negative-resistance effect. (As the plate voltage is increased, the velocity at which
primary electrons strike the plate and the number of secondary electrons that accordingly are emitted increase. The secondary
electrons are attracted back to the more positive screen, thereby reducing the plate current and resulting in the negative
slope from A to B in Fig. 6B.)
Grounded-Grid Amplifier. Under certain conditions, a grounded-grid amplifier provides negative resistance. One such condition
occurs in the telephone repeater amplifier, shown in simplified form in Fig. 7. This amplifier delivers power to the telephone
circuit in which it "rides," instead of absorbing power, hence qualifies as a negative resistance. Voice currents from the
transmitter (microphone) produce instantaneous currents represented by the dotted arrows, B and D. These currents, in turn,
cause a plate current, represented by the solid arrow C, which is opposite to D because of 180° phase shift by the tube.
This plate current induces a voltage across the line winding of the transformer, represented by solid arrow A, which is
in series-aiding to the transmitter voltage. This induced voltage, being in-phase with the speech voltage, aids the latter,
causing more current and power in the receiver. (One of the actions of a negative resistance is, as we have shown earlier
in this article, the delivering of power to the circuit.) When the amplifier is not operating, the voltage drop across the
transformer absorbs power (positive-resistance action).
Point-Contact Transistor. If positive feedback is introduced in a device which has a higher-than-1 current gain, the
input resistance of the device will be negative over a portion of the conduction characteristic. The point-contact transistor
is such a device. In Fig. 8A, positive feedback is provided by the external base resistor, Rb. As the d.c. input
(emitter) current is increased, as shown in Fig. 8B, the emitter voltage (Ve) increases positively to A and
then to B, then negatively from B to C, and positively again from C to D. The central negative-resistance region (BC), bounded
on each side by a positive-resistance region (AB and CD), gives the type of curve shown earlier in Fig. 2B, which is valued
for flip-flop applications. Viewed from emitter to ground, a point-contact transistor operated in this manner is a negative
Direct-Coupled Junction Transistor Duo. The junction transistor has a current gain of less than 1 when connected regeneratively
(common-base circuit), so it cannot be used directly as a negative resistance in the way that the point-contact transistor
can. However, two junction transistors may be connected in a manner such that a negative resistance is "seen" at the input
terminals of the circuit. In Fig. 9A, the common emitter resistor, Re is analogous to the common cathode resistor
in a cathode-
coupled tube circuit. Positive feedback voltage is developed across this resistor by the second transistor, V2.
The plot of V1 base voltage (Vb) vs base current (Ib) has the shape shown in Fig. 9B, a
negative-resistance region appearing between B and C. Viewed from the V1 base to ground, the circuit is a negative
resistance when Re has the proper value to place the operating point of V1 along the negative slope
(BC in Fig. 9B).
Uni-junction Transistor. This device, also called a double-based diode, consists of a bar of n-type silicon with an ohmic
(non-rectifying) base contact at each end and a single p-n junction near the top end. Fig. 10A shows a uni-junction circuit.
The junction is biased by the input voltage in such a way that its lower half is positive with respect to base 1 and acts
as an emitter, whereas its upper half is negative with respect to base 2 and acts as a collector. This simultaneous emitter
and collector action produces a negative-resistance characteristic (region CD in Fig. 10B).
Point-Contact Germanium Diode. The point-contact germanium diode exhibits negative resistance when biased highly in the
reverse direction. Fig. 11A shows the circuit. As the reverse current is increased from zero (Fig. 11B), the diode voltage
drop increases to A, showing positive resistance. As the current is increased further, the diode voltage drop then decreases
from A to B, revealing negative resistance which is available at terminals X-X. Unfortunately, the diode is overloaded when
in the negative-resistance condition and is soon damaged by overheating. This has prevented exploitation of the effect,
although the point-contact diode operated in this manner will oscillate, amplify, and provide bi-stable switching action.
Thermistor. The thermistor, a temperature-sensitive resistor, exhibits negative resistance over a portion of its EI characteristic,
which seems to be dependent upon internal heating to some extent. The thermistor is not a rectifying device, therefore it
has no polarity; current may be passed through it in either direction. Fig. 12A shows a thermistor circuit. Fig. 12B shows
the response: as the voltage (E) is increased, the thermistor current (I) increases from zero to point A, a peak dependent
upon internal and ambient temperatures and upon the composition of the thermistor material. As the voltage is increased
further, the current decreases, as from A to B, revealing negative resistance. The latter is available for use at terminals
Because negative resistance in the thermistor depends upon heat effects and since there can be appreciable thermal inertia
in the device, use of the thermistor in negative-resistance oscillators, amplifiers, and switching circuits is limited to
very low frequencies.
The devices chosen for review in this article are d.c.-operated, and they qualify as resistances. In addition to these,
there are certain a.c.-operated devices which can be made to display a negative slope in their conduction characteristics.
It would seem proper, however, to term these negative-impedance devices. In some applications, these devices are less flexible
than their d.c. counterparts because they require a.c. power supply (either a.f. or r.f.).
Such devices include ferro-resonant elements (ferristors), ferro-electric capacitors, voltage-sensitive capacitors (silicon
capacitors or varactors, and ceramic voltage-sensitive capacitors), and the several types of magnetic amplifier devices
and saturable reactors.
Posted June 16, 2016