Link Coupling Nomogram
January 1969 Electronics World

January 1969 Electronics World

January 1969 Electronics World Cover - RF Cafe  Table of Contents 

Wax nostalgic about and learn from the history of early electronics. See articles from Electronics World, published May 1959 - December 1971. All copyrights hereby acknowledged.

This nomogram (aka nomograph) provides a 'simple' method for determining the coupling coefficient (ke) of air core transformers for RF circuits where the operational wavelength is much longer than the physical length of the transformer. Modern circuit simulators can calculate such quantities at the blink of an eye, but in 1969 there was no simple method for doing it. In fact, a lot of design work back in the day was done using nomograms because given all the impreciseness of circuit layout and component tolerances, there were enough tunable elements provided to tweak for optimal performance. Unlike today where the use of sophisticated (and expensive) software can practically assure first-pass success with circuits into the realm of tens of GHz, multiple iterations of designs used to be the norm. As an electronics technician before earning my BSEE, I built and modified many circuits for the engineers I worked for before they went into production. We've come a long way, baby.

Link Coupling Nomogram

By Donald W. Moffat

Air-core transformers are often used to match the source impedance to the load - RF Cafe

Fig. 1. In radio-frequency circuits, air-core transformers are often used to match the source impedance to the load.

Calculating coupling coefficient values, ke, can be a tedious and messy mathematical process. But if the link coupling's physical length is less than the wavelength, this nomogram can do the job.

When a signal source is physically separated from the circuit it supplies, link coupling like that shown in Fig. 1 is often used to match impedances. A second transformer matches the link to the load. Although air-core radio frequency transformers are shown in the diagram, this method of coupling is equally applicable at low audio frequencies.

Link coupling would probably be used more often except that the mathematics discourages a designer from attempting to predict the over-all coupling coefficient, ke. However, if one assumes that the length of the link is significantly less than a wavelength of the frequency being coupled, then the equations become manageable. A nomogram can then be made and ke found without any calculations. As the length of the link approaches the wavelength, the nomogram becomes less dependable. And when the link is longer than a wavelength, this nomogram does not apply at all.

Using the Nomogram

Link Coupling Nomogram, January 1969 Electronics World - RF CafeIt will be helpful to first examine the curves in the upper left of the nomogram. The scale on the left and the background grid of light horizontal and vertical lines serve as guides when determining values of Effective k. Although only nine curves are drawn, the user should visualize an unlimited number of curves, all of the same shape, filling in the spaces.

When the instructions say to follow a curve from the vertical axis, it will often be necessary to picture a curve which starts from a given place on the axis, and follows the same shape as the others. This is shown in example.

To find ke on the nomogram, we must know the inductances of the windings at either end of the link and the coefficients of coupling of the two transformers. The order of the five steps in the following paragraphs should be adhered to when determining ke values.

(a) Locate the correct inductance values on the L3 and L4 scales and draw a straight line through these points, extending the line to cross the heavy horizontal line at the bottom of the curves.

(b) From that point on the heavy horizontal line, draw a vertical line straight up through the curves, using the nearest vertical grid line as a guide.

(c) Locate the correct values of individual coefficients of coupling on the k1 and k2 scales and draw a straight line through them. Extend this line and cross the heavy vertical line that bounds the curves on the right.

(d) Follow the curve which also intersects at this point on the heavy vertical line, until it intersects with the vertical line drawn in Step (b). It may happen that one of the curves in the drawing starts at that intersection, or it may be necessary to visualize a curve which has the same shape as the others.

(e) From the point where the curve intersects with the line drawn in Step (b), proceed straight out to the ke scale on the left. Use the nearest horizontal grid line as a guide and at the ke scale read the effective coefficient of coupling from input to output.

It is interesting to note that ke increases if either of the individual coefficients of coupling is increased and, for a given combination of k1 and k2, the maximum ke occurs when L3 is equal to L4. The value of maximum ke (when the inductances are equal) is equal to one-half the product of the individual coefficients of coupling, so a theoretical maximum of ke = 1/2 is approached when k1 and k2 both approach unity and both inductances have the same value.

Example

Find ke if the circuit diagram has L3 and L4 values of 10 and 7 microhenrys, respectively, and k1 and k2 values of 0.5 and 0.2. Total length of the link is significantly less than a wavelength of the frequency being coupled.

1. Draw a line from 7 on the L4 scale, through 10 on the L3 scale, to the heavy horizontal line that bounds the curves in the upper left corner.

2. Draw a line straight up from that point, parallel to the nearest vertical grid line.

3. Draw a line from 0.2 on the k2 scale, through 0.5 on the k1 scale, to the heavy vertical line that bounds the curves on their right.

4. The dotted curve shows how a curve should be visualized if a printed one does not meet the line drawn in Step 3. Follow the curve to where it intersects with the line drawn in Step 2.

5. From that intersection, use the nearest horizontal grid line as a guide and proceed straight out to the Effective k scale. Read the answer of ke = 0.084.

Since no units are shown on the L scales, the user of the nomogram can supply any set of units that applies to his circuit, as long as he uses the same units on both scales. For instance, both scales can be called microhenrys, millihenrys, or even tenths of a microhenry if such values would be most useful in a particular application.

 

 

Posted June 12, 2017