The concept of a decibel (dB) is understandably difficult and confusing for someone just being introduced
to it. Combining specifications for gain, power, and voltage (and current, but
not so often) that mix dB, dBm, dBW, watts, milliwatts, voltage, millivolts, etc., often requires
converting back and forth between linear values and decibel values. This brief tutorial will help to
clarify the difference between working with decibels and working with linear values.
Anxiety Alert: Using decibels involves working with logarithms.
Logarithms (logs) were first conceived of in the early 1600s by Scottish mathematician
John Napier, as a tool for simplifying
multiplication and division operations by converting them to faster and less error prone addition and subtraction operations,
respectively. This
is made possible because of the way multiplication of two numbers expressed as similar base numbers with
exponents can be accomplished by merely adding the exponents together. Division of those same numbers
is accomplished by subtracting the exponents. It is one of the laws of exponents, and looks like
this:
Using actual numbers as an example, where x = 10, a = 4, b = 1:
The law of exponents works for any base number, not just 10. To wit:
People tend to make fewer mistakes when adding and subtracting numbers, so the advantage of logarithms
is apparent. Remember that logarithms were developed before automatic mechanical or electronic computers
were available. A slide rule exploits the properties of logarithms for
calculation, but that is a separate major topic.
Those are simple examples, but hold for any base or exponent. In the absence of a calculator, in
order to be useful for general application you need a table of numbers and their equivalent logarithms.
Early log tables filled volumes, depending on the spacing between numbers (1.000,
1.001, 1.002, 1.003, vs. 1.0, 1.1, 1.2, 1.3, etc.). The good news for creators of
logarithm tables
is that only a single 'decade' of numbers (e.g., 1 through 10) is required since
every preceding or seceding decade is a simple multiple of a power of 10.
Note: I use base 10 in this discussion since that is the base of our common number system  hence
the term 'common logarithm' for base 10 logs. You might have heard of
natural logarithms, which
uses the base of e,
but e is not used very often when calculating scalar electrical power, voltage, and current quantities
(although it is used when phase angles are included, i.e.,
Euler's identity).
Natural logarithms are written as ln (x) without the 'e' subscript, whereas usually base 10 logarithms
are written simply as log (x) without the 10 subscript; i.e., not log_{e} (x) or log_{10} (x),
respectively.
Per a base=10 log table:
log (100,000) = 5,
log (10,000) = 4, log
(1,000) = 3, log (10) = 1
The exception and special case is log_{x} (0) =
Undefined. That is so because there is no power to which you can raise any number and obtain 0 (zero).
You can asymptotically approach zero, but you cannot get to zero. There will never be the number zero
displayed on a log scale; they usually run from some power of 10 to some other power of ten. An example
of log graph paper is shown on the right. It has 5 'cycles' or 'decades' of range. Note there is no
zero on the yaxis.
The base10 (common) logarithm of a number, then, is the exponent that 10 must be raised to in order
to obtain that number. In other words, since 10 raised to the power of 2 is equal to 100 (10^{2}
= 100), the base10 log of 100 is 2 (log_{10} 100 = 2).
This is the basic law of logarithms:
log_{c} (a) = b,
therefore c^{b} = a
Performing the same multiplications and divisions as done at the top of the page by using actual logarithms:
10,000 * 10 = 100,000 and 10,000 ÷ 10
= 1,000
4 + 1 = 5 and 4  1 = 3
That's fine, but what you end up with is the logarithm of the number you seek. Question: Except for a simple
example like this, how do you get the answer you need? Answer: Look up the antilogarithm (antilog) of
the result. In this case:
antilog 5 = 100,000 and antilog 3 =
1,000
A tougher, and more likely example with numbers that are not integer powers of 10, might look something like the following:
x = 1.28 * 3.70 * 0.559 * 26.4
log (x) = log (1.28) + log (3.70) + log (0.559) + log (26.4)
log (x) = 0.1072 + 0.5682 + (0.2526) + 1.4216 = 1.8444
Since the logarithm of 'x'
equals 1.8444, the antilog equals 'x,' which is 69.9
Check: x = 1.28 * 3.70 * 0.559 * 26.4 = 69.9
I used my calculator to look up the logs and antilogs for those numbers, but prior to 1972 when Hewlett Packard (HP)
introduced their HP35 scientific
calculator, the average person without access to a corporate or university mainframe computer needed to use a log table to perform such calculations.
Who bothers to use logarithms today, you might ask? Lots of people, including me, quite often when calculating
cascaded
system parameters like noise figure (NF) and intercept points (IP). Simple addition and subtraction of gain dB and power dBm values don't work
with NF and IP.
The governing formulas use multiplication and division of linear gain and power values, which
requires first converting dB and/or dBm to linear numbers (gain ratio and mW) using antilogs, performing the cascade calculations,
and then converting the result back to dB and/or dBm using logs.
Not all system cascade operations require converting back and forth. For instance if only the total
system gain and/or output power level is needed, then calculations can be carried out with either
linear units (mW and multipliers) or logarithmic units (dBm and dB, respectively).
The Definition of 'dB' and 'dBm'
A decibel (dB) in electrical engineering is defined as 10 times the base10 logarithm of a ratio
between two power levels; e.g., P_{out}/P_{in} (gain, in other words). To wit:
N dB = 10 * log_{10} (P1/P2)
All gains greater than 1 are therefore expressed as positive decibels (>0), and gains of less
than 1 are expressed as negative decibels (<0). Note that for cases most of us encounter, the linear
ratio of P1/P2 must be a positive number (>0) since the logarithm of 0 is undefined and the
logarithm of negatives numbers are complex (they contain both a real and an imaginary part). The dB
value, though, can theoretically take on any value between −∞ and +∞, including 0, which
is a gain of 1 [10 * log (1) = 0 dB].
'dBm' is a decibelbased unit of power that is referenced to 1 mW. Since 0 dB of gain is
equal to a gain of 1, 1 mW of power is 0 dB greater than 1 mW, or 0 dBm.
Similarly, a power unit of dBW is decibels relative to 1 W of power.
1 mW = 0 dBm
Accordingly, all dBm values greater than 0 are larger than 1 mW, and all dBm values less than
0 are smaller than 1 mW (see Fig. 1). For instance, +3.01 dBm is 3.01 dB greater than
1 mW; i.e., or 0 dBm + 3.01 dB = +3.01 dBm (2 mW). −3.01 dBm is 3.01 dB
less than 1 mW; i.e., or 0 dBm + (−3.01) dB = −3.01 dBm (0.5 mW).
The following table gives some numerical examples so you can see the correlation between mW and
dBm. The same set of values plotted on a logarithmic scale would produce a straight line. Because of the logarithmic
relationship, the graph bunches the smaller values against the left vertical axis. A magnified version
of the 0 to 1 mW region is inset for clarity.
Fig. 1  Graph of Power in Units of dBm vs. mW
Fig. 2 is a table and graph of dB vs. linear gain ratios similar to the dBm vs. mW in Fig. 1. Note
that the numbers and curves are exactly the same; only the axis labels are changed. That is because dBm is a unit
of power expressed in dB relative to 1 mW (0 dBm).
Fig. 2  Graph of Gain in Units of dBm vs. Linear Ratio
Linear Gain (output/input ratio) vs. Logarithmic (decibels, dB) Gain
Fundamentally, gain is a multiplication (or division) factor. As an example, an amplifier might have
a gain that increases the signal by a factor of 4 (i.e., 4x) from input to output (see Fig. 3). If a
1 mW (0 dBm) signal is fed into the amplifier, then 1 mW * 4 = 4 mW
comes out. In terms of decibels, a factor of 4 is equivalent to 10 * log (4) = 6.02 dB,
so 0 dBm in plus 6.02 dB of gain yields +6.02 dBm at the output.
1 mW * 4
= 4 mW
0 dBm + 6.02
dB = 6.02 dBm
Fig. 3  Single amplifier gain.
Combining Gains (linear and dB) w/Positive Values
If an amplifier with a gain of 4 is in series with a second amplifier with a gain of 6, then the
total gain is 4 * 6 = 24. In terms of decibels, a factor of 6 is equivalent to 10 * log (6) = 7.78 dB,
and a factor of 24 is equivalent to 10 * log (24) = 13.8 dB.
Just as 4 x 6 = 24 (linear gain), 6.02 dB + 7.78 dB = 13.8 dB
(decibel gain).
If a 1 mW signal (0 dBm) is fed into the amplifier, then 4 mW comes out of the first amplifier,
and 24 mW comes out of the second amplifier. See Fig. 4.
1 mW * 4
* 6 = 24 mW
0 dBm + 6.02
dB + 7.78 dB = 13.8 dBm
Fig. 4  Cascaded dual amplifier gain.
Combining Gain and Loss (linear and dB)
This next example shows what happens when a gain < 1 (a loss) is encountered, where an attenuator
with a gain of 1/6 is placed after the first amplifier instead of having a second amplifier. See
Fig. 5.
4 * 1/6 = 2/3 (linear gain). Similarly 6.02 dB  7.78 dB = −1.76 dB
(decibel gain).
As with the previous example, if a 1 mW signal (0 dBm) is fed into the amplifier with a gain
of 4, then 4 mW comes out. That 4 mW then goes into the attenuator with a linear gain of 1/6
and comes out at a power level of 4/6 mW (2/3 mW).
The total gain in this case is 4/6 = 2/3, so the output power will actually be less than the
input power.
1 mW * 4
* 1/6 = 2/3 mW = 0.67 mW
0 dBm + 6.02
dB + (7.78 dB) = −1.76 dBm
Fig. 5  Cascaded amplifier gain and attenuator.
Note that power levels greater than 0 dBm sometimes include the 'plus' sign (+) in order to
emphasize that it is not negative. This is particularly so when power levels are displayed on a block
diagram where both positive and negative values are present.
Summary
When making power measurements in the laboratory or in the field, most people find it easier to add
and subtract gains and power levels than to multiply and divide gains and power levels. dB and dBm units make that possible. The important
thing to remember is to never mix linear
gain (ratio) units and wattage power (mW) units with logarithmic gain (dB) and power (dBm) units.
Quantities must be either in all linear or all decibel units. The following type of calculation is NOT
allowed because it mixes linear values with logarithmic values.
12 mW + 34 mW + 8 mW + 20 dB
Supplemental Information on Logarithms
Logarithms of Products
A property of logarithms used implicitly above states the following, and is the basis for being able
to add and subtract logarithm values instead of multiplying their linear equivalents.
log (h*j)= log (h) + log (j), and log (h/j)= log
(h)  log (j)
therefore,
log (h*j/k*m/n) = log (h) + log (j)  log (k) + log (m)  log (n)
'h * j / k * m / n' might represent a cascade of components that have three devices (h, j, and m)
each with gain >1 and two devices (k and n) each with a gain <1 (see Fig. 6). The total system
gain can be calculated either by multiplying all the linear gain values together or adding all the decibel
gain values together.
Fig. 6  Cascaded components
See more on properties of logarithms
and properties of exponents.
Logarithms of Exponents
The following is important for understanding why power gain in terms of power is
10 * log (P_{out}/P_{in}) dB, while power gain in terms
of voltage is 20 * log (V_{out}/V_{in}) dB.
log (c^{f}) = f * log (c),
which is so because c^{f} is equal to c multiplied by itself 'f' times. For example, if f
= 4:
c^{f} = c^{4}
= c * c * c * c
log (c^{4}) = log (c * c * c * c) = log (c) + log (c) + log
(c) + log (c) = 4 * log (c).
Power Gain Based on Power vs. Power Gain Based on Voltage
Power gain is P_{out}/P_{in}, and voltage gain is V_{out}/V_{in}.
Power gain based on a power ratio in decibels is defined as 10 * log (P_{out}/P_{in}). Power
gain in terms of voltage, is [(V_{out}^{2}/R)/(V_{in}^{2}/R)],
since per Ohm's law P = V^{2}/R.
The 'R' in the denominators cancel leaving V_{out}^{2}/V_{in}^{2} ,
which is equal to (V_{out}/V_{in})^{2}, as defined by the rule of exponents
that says
a^{c}/b^{c} = (a/b)^{c}. Hence:
10 * log = 10 * 2 * log = 20 *
log
Important Note: Voltage gain in terms of voltage is 10 * log (V_{out}/V_{in}) dB,
the same as with power gain in terms of power. It is only when power gain
is expressed in terms of voltage that the 20 * log (V_{out}/V_{in}) dB
equation applies. This is a common point of confusion.
Gain <1 (Loss) as Negative Decibels
No operation in mathematics is arbitrary, and that goes for why a signal power loss (gain <1)
is portrayed as a negative value, and hence is subtracted during a cascade calculation. It is a simple
demonstration, but worthy of mentioning.
log (1/f) = log (1)  log (f) = 0  log (f) = log (f)
Please send any comments or corrections to
.
Posted October 18, 2016
