Navy Electricity and Electronics Training Series (NEETS)
10—Introduction to Wave Propagation, Transmission Lines,
Chapter 3: Pages 3-1 through 3-10
Module 10—Introduction to Wave Propagation, Transmission Lines, and Antennas
i - ix
, 1-1 to 1-10
1-11 to 1-20
, 1-21 to 1-30
1-31 to 1-40
1-41 to 1-47
2-1 to 2-10
, 2-11 to 2-20
2-21 to 2-30
, 2-31 to 2-40
2-40 to 2-47
, 3-1 to 3-10
3-11 to 3-20
3-21 to 3-30
3-31 to 3-40
, 3-41 to 3-50
3-51 to 3-58
, 4-1 to 4-10
4-11 to 4-20
, 4-21 to 4-30
4-31 to 4-40
, 4-41 to 4-50
4-51 to 4-60
PRINCIPLES OF TRANSMISSION LINES
Upon completion of this chapter, you will be able to:
1. State what a transmission line is and
how transmission lines are used.
2. Explain the operating principles of transmission lines.
Describe the five types of transmission lines.
4. State the length of a transmission line.
Explain the theory of the transmission line.
6. Define the term LUMPED CONSTANTS in relation to a transmission line.
7. Define the term DISTRIBUTED
CONSTANTS in relation to a transmission line.
8. Define LEAKAGE CURRENT.
9. Describe how the electromagnetic lines of force around a transmission line are affected by the distributed
10. Define the term CHARACTERISTIC IMPEDANCE and explain how it affects the transfer of
energy along a transmission line.
11. State how the energy transfer along a transmission line is
affected by characteristic impedance and the infinite line.
12. Identify the cause of and describe the
characteristics of reflections on a transmission line.
13. Define the term STANDING WAVES as applied to
a transmission line.
14. Describe how standing waves are produced on a transmission line and identify
the types of terminations.
15. Describe the types of standing-wave ratios.
INTRODUCTION TO TRANSMISSION LINES
A TRANSMISSION LINE is a device designed to guide electrical energy from one point to another. It is
used, for example, to transfer the output rf energy of a transmitter to an antenna. This energy will not travel
through normal electrical wire without great losses. Although the antenna can be connected directly to the
transmitter, the antenna is usually located some distance away from the transmitter. On board ship,
the transmitter is located inside a radio room and its associated antenna is mounted on a mast. A
transmission line is used to connect the transmitter and the antenna.
The transmission line has a single
purpose for both the transmitter and the antenna. This purpose is to transfer the energy output of the transmitter
to the antenna with the least possible power loss. How well this is done depends on the special physical and
electrical characteristics (impedance and resistance) of the transmission line.
All transmission lines have two ends (see figure 3-1). The end of a two-wire transmission line connected to a
source is ordinarily called the INPUT END or the GENERATOR END. Other names given to this end are TRANSMITTER END,
SENDING END, and SOURCE. The other end of the line is called the OUTPUT END or RECEIVING END. Other names given to
the output end are LOAD END and SINK.
Figure 3-1.—Basic transmission line.
You can describe a transmission line in terms of its impedance. The ratio of voltage to current
(Ein/Iin) at the input end is known as the INPUT IMPEDANCE (Zin). This is the impedance presented to the
transmitter by the transmission line and its load, the antenna. The ratio of voltage to current at the output
(Eout/Iout) end is known as the OUTPUT IMPEDANCE (Zout). This is the impedance presented to the load by the
transmission line and its source. If an infinitely long transmission line could be used, the ratio of voltage to
current at any point on that transmission line would be some particular value of impedance. This impedance is
known as the CHARACTERISTIC IMPEDANCE.
Q1. What connecting link is used to transfer energy from a radio transmitter to its antenna located on the mast
of a ship?
Q2. What term is used for the end of the transmission line that is connected to a
Q3. What term is used for the end of the transmission line that is connected to an antenna?
TYPES OF TRANSMISSION MEDIUMS
The Navy uses many different types of TRANSMISSION MEDIUMS in its
electronic applications. Each medium (line or wave guide) has a certain characteristic impedance value,
current-carrying capacity, and physical shape and is designed to meet a particular requirement.
The five types of transmission mediums that we will discuss in this chapter include PARALLEL-LINE,
TWISTED PAIR, SHIELDED PAIR, COAXIAL LINE, and WAVEGUIDES. The use of a particular line depends, among other
things, on the applied frequency, the power-handling capabilities, and the type of installation.
NOTE: In the following paragraphs, we will mention LOSSES several times. We will discuss these losses
more thoroughly under "LOSSES IN TRANSMISSION LINES."
Two-Wire Open Line
of parallel line is the TWO-WIRE OPEN LINE illustrated in figure 3-2. This line consists of two wires that are
generally spaced from 2 to 6 inches apart by insulating spacers. This type of line is most often used for power
lines, rural telephone lines, and telegraph lines. It is sometimes used as a transmission line between a
transmitter and an antenna or between an antenna and a receiver. An advantage of this type of line is its simple
construction. The principal disadvantages of this type of line are the high radiation losses and electrical noise
pickup because of the lack of shielding. Radiation losses are produced by the changing fields created by the
changing current in each conductor.
Figure 3-2.—Parallel two-wire line.
Another type of parallel line is the TWO-WIRE RIBBON (TWIN LEAD) illustrated in figure 3-3. This type of
transmission line is commonly used to connect a television receiving antenna to a home television set. This line
is essentially the same as the two-wire open line except that uniform spacing is assured by embedding the two
wires in a low-loss dielectric, usually polyethylene. Since the wires are embedded in the thin ribbon of
polyethylene, the dielectric space is partly air and partly polyethylene.
Figure 3-3.—Two-wire ribbon type line.
The TWISTED PAIR transmission line is illustrated in figure 3-4. As the
name implies, the line consists of two insulated wires twisted together to form a flexible line without the use of
spacers. It is not used for transmitting high frequency because of the high dielectric losses that occur in the
rubber insulation. When the line is wet, the losses increase greatly.
Figure 3-4.—Twisted pair.
The SHIELDED PAIR, shown in figure 3-5, consists of parallel
conductors separated from each other and surrounded by a solid dielectric. The conductors are contained within a
braided copper tubing that acts as an electrical shield. The assembly is covered with a rubber or flexible
composition coating that protects the line from moisture and mechanical damage. Outwardly, it looks much like the
power cord of a washing machine or refrigerator.
Figure 3-5.—Shielded pair.
The principal advantage of the shielded pair is that the conductors are balanced to ground; that is, the
capacitance between the wires is uniform throughout the length of the line. This balance is due to the uniform
spacing of the grounded shield that surrounds the wires along their entire length. The braided copper shield
isolates the conductors from stray magnetic fields.
There are two
types of COAXIAL LINES, RIGID (AIR) COAXIAL LINE and FLEXIBLE (SOLID) COAXIAL LINE. The physical construction of
both types is basically the same; that is, each contains two concentric conductors.
The rigid coaxial line consists of a central, insulated wire (inner conductor) mounted inside a
tubular outer conductor. This line is shown in figure 3-6. In some applications, the inner conductor is also
tubular. The inner conductor is insulated from the outer conductor by insulating spacers or beads at regular
intervals. The spacers are made of Pyrex, polystyrene, or some other material that has good insulating
characteristics and low dielectric losses at high frequencies.
Figure 3-6.—Air coaxial line.
The chief advantage of the rigid line is its ability to minimize radiation losses. The electric and
magnetic fields in a two-wire parallel line extend into space for relatively great distances and radiation losses
occur. However, in a coaxial line no electric or magnetic fields extend outside of the outer conductor. The fields
are confined to the space between the two conductors, resulting in a perfectly shielded coaxial line. Another
advantage is that interference from other lines is reduced.
The rigid line has the following
disadvantages: (1) it is expensive to construct; (2) it must be kept dry to prevent excessive leakage between the
two conductors; and (3) although high-frequency losses are somewhat less than in previously mentioned lines, they
are still excessive enough to limit the practical length of the line.
Leakage caused by the condensation
of moisture is prevented in some rigid line applications by the use of an inert gas, such as nitrogen, helium, or
argon. It is pumped into the dielectric space of the line at a pressure that can vary from 3 to 35 pounds per
square inch. The inert gas is used to dry the line when it is first installed and pressure is maintained to ensure
that no moisture enters the line.
Flexible coaxial lines (figure 3-7) are made with an inner conductor that consists of flexible wire insulated from
the outer conductor by a solid, continuous insulating material. The outer conductor is made of metal braid, which
gives the line flexibility. Early attempts at gaining flexibility involved using rubber insulators between the two
conductors. However, the rubber insulators caused excessive losses at high frequencies.
Figure 3-7.—Flexible coaxial line.
Because of the high-frequency losses associated with rubber insulators, polyethylene plastic was
developed to replace rubber and eliminate these losses. Polyethylene plastic is a solid substance that remains
flexible over a wide range of temperatures. It is unaffected by seawater, gasoline, oil, and most other liquids
that may be found aboard ship. The use of polyethylene as an insulator results in greater high-frequency losses
than the use of air as an insulator. However, these losses are still lower than the losses associated with most
other solid dielectric materials.
The WAVEGUIDE is classified as a
transmission line. However, the method by which it transmits energy down its length differs from the conventional
methods. Waveguides are cylindrical, elliptical, or rectangular (cylindrical and rectangular shapes are shown in
figure 3-8). The rectangular waveguide is used more frequently than the cylindrical waveguide.
The term waveguide can be applied to all types of transmission lines in the sense that they are all used
to guide energy from one point to another. However, usage has generally limited the term to mean a hollow metal
tube or a dielectric transmission line. In this chapter, we use the term waveguide only to mean "hollow metal
tube." It is interesting to note that the transmission of electromagnetic energy along a waveguide travels at a
velocity somewhat slower than electromagnetic energy traveling through free space.
A waveguide may be
classified according to its cross section (rectangular, elliptical, or circular), or according to the material
used in its construction (metallic or dielectric). Dielectric waveguides are
seldom used because the dielectric losses for all known dielectric materials are too great to transfer
the electric and magnetic fields efficiently.
The installation of a complete waveguide transmission system
is somewhat more difficult than the installation of other types of transmission lines. The radius of bends in the
waveguide must measure greater than two wavelengths at the operating frequency of the equipment to avoid excessive
attenuation. The cross section must remain uniform around the bend. These requirements hamper installation in
confined spaces. If the waveguide is dented, or if solder is permitted to run inside the joints, the attenuation
of the line is greatly increased. Dents and obstructions in the waveguide also reduce its breakdown voltage, thus
limiting the waveguide’s power-handling capability because of possible arc over. Great care must be exercised
during installation; one or two carelessly made joints can seriously inhibit the advantage of using the waveguide.
We will not consider the waveguide operation in this module, since waveguide theory is discussed in NEETS,
Module 11, Microwave Principles.
Q4. List the five types of transmission lines in use today.
Q5. Name two of the three described uses of a two-wire open line.
Q6. What are the two primary
disadvantages of a two-wire open line?
Q7. What type of transmission line is often used to connect a
television set to its antenna?
Q8. What is the primary advantage of the shielded pair?
What are the two types of coaxial lines in use today?
Q10. What is the chief advantage of the air
Q11. List the three disadvantages of the air coaxial line.
Q12. List the two
common types of waveguides in use today.
LOSSES IN TRANSMISSION LINES
The discussion of transmission lines so far has not directly
addressed LINE LOSSES; actually some line losses occur in all lines. Line losses may be any of three types—COPPER,
DIELECTRIC, and RADIATION or INDUCTION LOSSES.
NOTE: Transmission lines are sometimes
referred to as rf lines. In this text the terms are used interchangeably.
One type of copper loss is I2R LOSS. In rf lines the resistance of the conductors is never equal to zero. Whenever
current flows through one of these conductors, some energy is dissipated in the form of heat. This heat loss is a
POWER LOSS. With copper braid, which has a resistance higher than solid tubing, this power loss is higher.
Another type of copper loss is due to SKIN EFFECT. When dc flows through a conductor, the movement of electrons
through the conductor's cross section is uniform. The situation is somewhat different when ac is applied. The
expanding and collapsing fields about each electron encircle other electrons. This phenomenon, called SELF
INDUCTION, retards the movement of the encircled electrons.
The flux density at the center is so great that electron movement at this point is reduced. As
frequency is increased, the opposition to the flow of current in the center of the wire increases. Current in the
center of the wire becomes smaller and most of the electron flow is on the wire surface. When the frequency
applied is 100 megahertz or higher, the electron movement in the center is so small that the center of the wire
could be removed without any noticeable effect on current. You should be able to see that the effective
cross-sectional area decreases as the frequency increases. Since resistance is inversely proportional to the
cross-sectional area, the resistance will increase as the frequency is increased. Also, since power loss increases
as resistance increases, power losses increase with an increase in frequency because of skin effect.
Copper losses can be minimized and conductivity increased in an rf line by plating the line with silver. Since
silver is a better conductor than copper, most of the current will flow through the silver layer. The tubing then
serves primarily as a mechanical support.
DIELECTRIC LOSSES result from the heating effect on the dielectric
material between the conductors. Power from the source is used in heating the dielectric. The heat produced is
dissipated into the surrounding medium. When there is no potential difference between two conductors, the atoms in
the dielectric material between them are normal and the orbits of the electrons are circular. When there is a
potential difference between two conductors, the orbits of the electrons change. The excessive negative charge on
one conductor repels electrons on the dielectric toward the positive conductor and thus distorts the orbits of the
electrons. A change in the path of electrons requires more energy, introducing a power loss.
structure of rubber is more difficult to distort than the structure of some other dielectric materials. The atoms
of materials, such as polyethylene, distort easily. Therefore, polyethylene is often used as a dielectric because
less power is consumed when its electron orbits are distorted.
Radiation and Induction Losses
RADIATION and INDUCTION LOSSES are similar in that both are caused by the fields surrounding the conductors.
Induction losses occur when the electromagnetic field about a conductor cuts through any nearby metallic object
and a current is induced in that object. As a result, power is dissipated in the object and is lost.
Radiation losses occur because some magnetic lines of force about a conductor do not return to the conductor when
the cycle alternates. These lines of force are projected into space as radiation and this results in power losses.
That is, power is supplied by the source, but is not available to the load.
Q13. What are the three
types of line losses associated with transmission lines?
Q14. Losses caused by skin effect and the I2R
(power) loss are classified as what type of loss?
Q15. What types of losses cause the dielectric
material between the conductors to be heated?
LENGTH OF A TRANSMISSION LINE
A transmission line is considered to be
electrically short when its physical length is short compared to a quarter-wavelength (1/4λ)
of the energy it is to carry.
NOTE: In this module, for ease of reading, the value of the
wavelength will be spelled out in some cases, and in other cases, the numerical value will be used.
A transmission line is electrically long when its physical length is long compared to a quarter-
wavelength of the energy it is to carry. You must understand that the terms "short" and "long" are relative ones.
For example, a line that has a physical length of 3 meters (approximately 10 feet) is considered quite short
electrically if it transmits a radio frequency of 30 kilohertz. On the other hand, the same transmission line is
considered electrically long if it transmits a frequency of 30,000 megahertz.
To show the difference in
physical and electrical lengths of the lines mentioned above, compute the wavelength of the two frequencies,
taking the 30-kilohertz example first:
Now, computing the wavelength for the line carrying 30,000 megahertz:
Thus, you can see that a 3-meter line is electrically very short for a frequency of 30 kilohertz. Also,
the 3-meter line is electrically very long for a frequency of 30,000 megahertz.
When power is applied to a
very short transmission line, practically all of it reaches the load at the output end of the line. This very
short transmission line is usually considered to have practically no electrical properties of its own, except for
a small amount of resistance.
However, the picture changes considerably when a long line is used. Since most transmission lines are
electrically long (because of the distance from transmitter to antenna), the properties of such lines must be
considered. Frequently, the voltage necessary to drive a current through a long line is considerably greater than
the amount that can be accounted for by the impedance of the load in series with the resistance of the line.
TRANSMISSION LINE THEORY
The electrical characteristics of a two-wire transmission line depend primarily on the construction of
the line. The two-wire line acts like a long capacitor. The change of its capacitive reactance is noticeable as
the frequency applied to it is changed. Since the long conductors have a magnetic field about them when electrical
energy is being passed through them, they also exhibit the properties of inductance. The values of inductance and
capacitance presented depend on the various physical factors that we discussed earlier. For example, the type of
line used, the dielectric in the line, and the length of the line must be considered. The effects of the inductive
and capacitive reactances of the line depend on the frequency applied. Since no dielectric is perfect, electrons
manage to move from one conductor to the other through the dielectric. Each type of two-wire transmission line
also has a conductance value. This conductance value represents the value of the current flow that may be expected
through the insulation. If the line is uniform (all values equal at each unit length), then one small section of
the line may represent several feet. This illustration of a two-wire transmission line will be used throughout the
discussion of transmission lines; but, keep in mind that the principles presented apply to all transmission lines.
We will explain the theories using LUMPED CONSTANTS and DISTRIBUTED CONSTANTS to further simplify these
A transmission line has the properties of inductance, capacitance, and
resistance just as the more conventional circuits have. Usually, however, the constants in conventional circuits
are lumped into a single device or component. For example, a coil of wire has the property of inductance. When a
certain amount of inductance is needed in a circuit, a coil of the proper dimensions is inserted. The inductance
of the circuit is lumped into the one component. Two metal plates separated by a small space, can be used to
supply the required capacitance for a circuit. In such a case, most of the capacitance of the circuit is lumped
into this one component. Similarly, a fixed resistor can be used to supply a certain value of circuit resistance
as a lumped sum. Ideally, a transmission line would also have its constants of inductance, capacitance, and
resistance lumped together, as shown in figure 3-9. Unfortunately, this is not the case. Transmission line
constants are distributed, as described below.
Introduction to Matter, Energy, and Direct Current, Introduction
to Alternating Current and Transformers, Introduction to Circuit Protection,
Control, and Measurement, Introduction to Electrical Conductors, Wiring Techniques,
and Schematic Reading, Introduction to Generators and Motors,
Introduction to Electronic Emission, Tubes, and Power Supplies,
Introduction to Solid-State Devices and Power Supplies,
Introduction to Amplifiers, Introduction to
Wave-Generation and Wave-Shaping Circuits, Introduction to Wave Propagation, Transmission
Lines, and Antennas, Microwave Principles,
Modulation Principles, Introduction to Number Systems and Logic Circuits, Introduction
to Microelectronics, Principles of Synchros, Servos, and Gyros,
Introduction to Test Equipment, Radio-Frequency
Communications Principles, Radar Principles, The Technician's Handbook,
Master Glossary, Test Methods and Practices, Introduction to Digital Computers,
Magnetic Recording, Introduction to Fiber Optics
Copyright: 1996 - 2024
BSEE - KB3UON
RF Cafe began life in 1996 as "RF Tools" in an AOL screen name web space totaling
2 MB. Its primary purpose was to provide me with ready access to commonly needed formulas
and reference material while performing my work as an RF system and circuit design engineer.
The Internet was still largely an unknown entity at the time and not much was available
in the form of WYSIWYG
All trademarks, copyrights, patents, and other rights of ownership to images and text
used on the RF Cafe website are hereby acknowledged.
My Hobby Website: AirplanesAndRockets.com